Home    Contact    
• DOOR
  Steel Roll-Up
     Steel
     Weatherized
     Insulated
     26 Guage Light Duty
  Aluminum Roll-Up
     Aluminum
     Insulated
     Grille
     Panel
     Lexan
     Lexan Panel
     Combination
     High Speed Door
  Counter Roll-Up
     Steel
     Aluminum
     Stainless Steel
  High Speed Roll-Up
     Aluminum
     Grille
     Steel
  Fire Rated Roll-Up
  Folding Closure
  Overhead Sectional
  Strip Door
  Swing Door
• OPERATOR
  Motor Operation
  Accessories
LEXAN PANEL ROLL-UP

Lexan Panel Roll-Up Doors can be manufactured to fit openings of any width and height to meet a diversity of commercial and residential application requirements. Possible applications include, but are not limited to, storefronts, banks, shopping-mall security, and many other applications where a combination of high security and visibility is required. Doors can be motor, chain hoist, crank or manually operated. Weatherstripped guides are standard to minimized rain infiltration, dust, wind and rodents. Additional weatherstripping for hood and sill is available.





ARCHITECTURAL SPECIFICATIONS

• GENERAL SPECIFICATIONS
Work Included
Lexan Roll-Up Doors will be designated as Model LA__ as manufactured by Best Roll-Up Door, Inc.
- Mounting: The doors can be face mounted or mounted between jams of a prepared opening.
Related Work
Opening preparations, miscellaneous or structural steel, field painting or finish, access panels, electrical wires, wiring, switch connection, conduit will be handled by the appropriate trades.
• PRODUCT SPECIFICATIONS
Curtain
- Slats: Aluminum panels extruded in continuous lengths of 6063-T6 anodized aluminum, cut to specific sizes for proper design and operation, interlocked alternately with solid Lexan (poly-carbonate) panels to form curtains.
- Gauge: Dual-faced aluminum panels shall have thickness of 16 gauge on each face. Lexan panels shall have thickness, where it is the minimum, of 0.15625" and, where it is the maximum, of 0.40625".
- Endlocks: To accomplish slat alignment and serve as a wearing surface endlocks are fitted to each end of alternate slats.
- Anodizing: All aluminum parts shall be anodized. Mill finish and shiny bright-dip anodized finish is also available.
Bottom Track
Curtain is reinforced with an extruded aluminum tube that can be further reinforced for wider openings.
Guide and Wall Angle Assembly
- Guides/Wall Angles: Extruded aluminum channels at both sides shall serve as guides. Wall angles shall be either aluminum or steel with minimum thickness of 1/8". Structural steel tubes can also be used in lieu of wall angles.
- Depth of Guide: To be of appropriate size to allow slate penetration and to restrict horizontal slat movement.
Bracket Plates
- Bracket Plates: To support the curtain and the counterbalance, the bracket plates shall be provided with minimum thickness of 1/4".
- Drive End Bracket Plate: The bracket plate on the drive-end is to be fitted with a sealed ball bearing.
Spring Counterbalance
- Counterbalance: Housed in a steel pipe, maximum deflection to 0.03" per foot of door width is achieved by having the appropriate diameter and wall thickness.
- Springs: Helical torsion with a 25% overload factor for ease of operation and are greased packed mounted on a cold rolled steel inner shaft.
- Spring Tension: Can be adjusted from outside of end bracket plate.
- Ball Bearing: Sealed in order to minimize wear of pipe shaft rotation around inner shaft.
HOODS
- Hoods: To completely enclose curtain and counterbalance, hoods shall be provided from #24 U.S. Gauge galvanized steel.
- Reinforcing: Can be reinforced laterally to prevent sag.
- Intermediate Hood Supports: Provided where door width exceeds 16'.
OPERATION
Operation can be manual push-up, chain hoist, waist high crank hoist, or electric motor operated.
LOCKING
- Integral Gearing: Power operator can serve as an additional locking for the door.
- Hand Chain Lock: Locking bracket can be provided.
- Cylinder Lock: System is installed in bottom track and can be key or thumb knob operated.
FINISH
Aluminum surfaces are anodized and can be powder coated in various colors upon request.

• EXECUTION
Installation
Installation to be completed by an authorized representative.
Options
- Bottom Track: Bottom track can be sloped to match contour on finished floor or can be notched to match obstruction on finished floor.
- Sensor Edge: An electronic sensor edge can be added to power operated doors to reverse the door travel upon encountering an obstruction for safety.
- High Cycle Springs: Can be obtained for motorized doors that require 50,000 to 100,000 cycles. Very high cycles in excess of 100,000 are also available.
- Locking: Thumb turn/key cylinder locks and multi-cylinder locks are available.
- Aluminum Surfaces: Aluminum surfaces can have mill finish or clear anodized finish.
- Pass Door: Hollow metal pedestrian door within rolling door can be obtained in a 3¡¯ x 7¡¯ or 3¡¯ x 6¡¯ 8¡± size. Hinged to rolling door guide the hollow metal door frame will swing clear of opening when desired. Hardware includes heavy duty hinges and handicap-level lock set.







13202 ARCTIC CIRCLE SANTA FE SPRINGS, CA 90670  •  TEL. 562.802.2233  •  TOLL FREE. 800.400.2565  •  BESTROLLUP@GMAIL.COM
(TEXAS BRANCH OFFICE) 2801 CARTERTON WAY FLOWER MOUND, TX 75022-5181 •  TEL. 469.909.8901
COPYRIGHT © 2014  BESTROLLUP.COM  All RIGHTS RESERVED